هوالرزاق


دسته بندی
ماژول سنسور آتش و شعله مادون قرمز
ماژول سنسور آتش و شعله مادون قرمز ماژول سنسور آتش و شعله مادون قرمز ماژول سنسور آتش و شعله مادون قرمز ماژول سنسور آتش و شعله مادون قرمز

ماژول سنسور آتش و شعله مادون قرمز

کد انبار : 309-110-1271
مدل کالا : FIRE-SENSOR
جستارش : B1-01-0409A
موجودی: 104
قیمت:
17,950 تومان

تعداد: - +
   - یا -   

ماژول سنسور آتش و شعله مادون قرمز

این برد یک ماژول گیرنده ی مادون قرمز است که بر روی آن یک آی سی مقایسه کننده به نام LM393 قرار دارد. سنسور شعله را می توان برای تشخیص منبع آتش و یا سایر منابع نور از طول موج در محدوده 760nm - 1100 نانومتر استفاده کرد. فاصله تشخیص فندک تست 80 سانتیمتر است و هر چقدر آتش بزرگ تر باشد فاصله تست می تواند بیشتر شود . زاویه ی تشخیص این سنسور نیز 60 درجه است و حساسیت قابل تنظیم دارد که با پتانسیومتر (به رنگ آبی در شکل مشخص است ) تنظیم می شود. این سنسور میتواند به عنوان زنگ خطر آتش سوزی و اهداف دیگر مورد استفاده قرار می گیرد . یک رابطه خروجی به طور مستقیم با پورت IO میکروکنترلر ارتباط برقرار می کند.
پایه های این ماژول 3 عدد و با نام های VCC، GND و DO برای اتصال به منبع تغذیه، زمین و خروجی دیجیتال می باشند.این ماژول کوچک با ولتاژ کاری 3.3 ولت تا 5 ولت، دارای سوراخ نصب است.


کاربرد سنسور آتش و شعله:

  1. پروژه های صنعتی
  2. تشخیص و هشدار آتش سوزی
  3. سسیستم هشدار دهنده
  4. ربات های آتش نشانی
  5. حساسیت محیطی
  6. سیستم اتوماسیون خانگی
  7. سیستم های امنیتی و آتش نشانی

مشخصات ماژول سنسور آتش و شعله :

  1. ولتاژ : 3.5 تا 5  ولت
  2. خروجی : دیجیتال DO
  3. دارای حفره ی نصب برای اتصال آسان به بدنه ی پروژه ها
  4. اندازه : 3.2cmx1.4cm
  5. استفاده از یک مقایسه کننده LM393 ولتاژ
  6. نزدیکی بیش از حد سنسور با آتش میتواند آسیب های حرارتی به آن وارد نماید

مستندات:
دیتاشیت سنسور شعله


Description:
A flame detector is a sensor designed to detect and respond to the presence of a flame or fire, allowing flame detection. Responses to a detected flame depend on the installation but can include sounding an alarm, deactivating a fuel line (such as a propane or a natural gas line), and activating a fire suppression system. When used in applications such as industrial furnaces, their role is to provide confirmation that the furnace is working properly; it can be used to turn off the ignition system though in many cases they take no direct action beyond notifying the operator or control system. A flame detector can often respond faster and more accurately than a smoke or heat detector due to the mechanisms it uses to detect the flame.
The LM393 series are dual independent precision voltage comparators capable of single or split supply operation. These devices
are designed to permit a common mode range−to−ground level with the single-supply operation. Input offset voltage specifications as low as
2.0 mV makes this device an excellent selection for many applications in consumer, automotive, and industrial electronics.

Note: The power supply must not be reversed, otherwise it is possible to damage the chip


Applications:
Various flames, fire source detection.

Features:
1. It can detect flame or wavelength in the range of 760 nm ~ 1100 nm light source, lighter test flame distance is 80cm, the greater the flame, the farther the test distance.
2. The detection angle 60 degrees or so, especially sensitive to the flame spectrum.
3. Sensitivity adjustable (blue digital potentiometer adjustment in the figure).
4. Comparator output, signal clean, good waveform, strong driving ability, more than 15mA.
5. With adjustable precision potentiometer Adjusting sensitivity.
6. Working voltage 3.3~5V.
7. Output form: digital switch output (0 and 1).
8. With fixed bolt holes for easy installation.
9. Small board PCB size: 3.2cm x 1.4cm.
10. Wide use Operating Instructions for Voltage LM393 Comparator.

Wiring Instructions:

1. VCC is connected to the positive pole of the power supply 3.3-5V
2. GND is connected to the negative power supply
3. DO TTL switch signal output

از این پس درج نظرات صرفا از طریق سامانه آفتاب یار امکان پذیر می باشد، برای وارد شدن به صفحه کالا بر روی لینک زیر کلیک کنید:
http://aftabyar.com/page/aftab-309.html
AftabRayaneh©2022