هوالرزاق


دسته بندی
شیلد دیتا لاگر آردوینو Arduino Data Logging Shield
شیلد دیتا لاگر آردوینو Arduino Data Logging Shield شیلد دیتا لاگر آردوینو Arduino Data Logging Shield شیلد دیتا لاگر آردوینو Arduino Data Logging Shield شیلد دیتا لاگر آردوینو Arduino Data Logging Shield

شیلد دیتا لاگر آردوینو Arduino Data Logging Shield

کد انبار : 1661-68-3040
مدل کالا : XD-204 Data Logger
جستارش : A2-16-0104A
موجودی: 1
قیمت:
90,900 تومان

تعداد: - +
   - یا -   

شیلد دیتا لاگر آردوینو Arduino Data Logging Shield

شیلد دیتا لاگر برای ذخیره سازی اطلاعاتی که بعد از قطع برق نباید از بین برود استفاده میشود . در واقع این ماژول برای ارتباط بین میکرو کنترلر(آردوینو) با یک SD کارت استفاده میشود . این ماژول سامل تمام قطعات مورد نیاز برای راه اندازی یک SD کارت میباشد و کاربر را بی نیاز به طراحی مدار برای ارتباط با ماژول میکند.

این ماژول علاوه بر داشتن راه انداز SD کارت یک RTC نیز بروی این ماژول تعبیه شده است .

فرض کنید که میخواهید دمای یک اتاق را در ساعت و تاریخ های مشخصی   ذخیره کنید برای این کار نیاز به دو ماژول جدا RTC برای شمارش ساعت ، تاریخ به صورت دقیق و یک SD کارت برای ذخیره سازی اطلاعات . این شیلد هر دوی این قطعات را در قالب یک ماژول در اختیار شما قرار میدهد


کاربرد شیلد DATA Logging آردوینو:

  1. ذخیره فایل‌ روی مموری SD با فرمت FAT16 و FAT32

مشخصات شیلد DATA Logging آردوینو:

  1. ولتاژ کاری: 3.3 ولت
  2. نوع باتری: CR1220 3V
  3. ابعاد: 68x52x19mm


برد های سازگار با شیلد دیتا لاگر آردوینو :

  1. آردوینو UNO
  2. آردوینو Leonardo
  3. آردوینو Mega
  4. آردوینو

مستندات:
طلاعات راه اندازی شیلد دیتا لاگر


Description:
The Data Logger shield comes tested assembled with all components and SD socket already on it, but you'll still need to put headers on so you can plug it into an Arduino. This Arduino data log shield is a dedicated, well-designed, and not expensive data logging shield Which is originally designed by DEEK ROBOT. This popular shield is"R3" compatible, so you can use it with just about any Arduino. The big SD card slot can fit any SD/MMC storage up to 32G and small as 32MB(Anything formatted FAT16 or FAT32). This shield included RTC (Real Time Clock) can be used to timestamp all your data with the current time.


Features:

Operating Voltage: 3.3V
Battery: CR1220 3V
Size: 68x52x19 mm


With this version you can use it with:

Arduino UNO or ATmega328 compatible - 4 analog channels at 10-bit resolution, 6 if RTC is not used
Arduino Leonardo or ATmega32u4 compatible - 12 analog channels at 10-bit resolution
Arduino Mega or ATmega2560 compatible - 16 analog inputs (10-bit)
Arduino Zero or ATSAMD21 compatible - 6 analog inputs (12-bit)
Arduino Due compatible - 12 analog inputs (12-bit)


Note:

1. If you have a UNO with a USB type B connector this shield may NOT WORK because the male pins are NOT LONG ENOUGH. You can prove this by forcing the D10 - D13 pins down when running your sketch. You may find then that the SD card works but as soon as you let go you will probably get a card read/write error. This shield works best, therefore, on an Arduino UNO with a USB type A connector or Micro USB connector.
2. Arduino Leonardo - The SD card is an SPI device but the shield has no ICSP connector. On an Arduino Leonardo, SPI is only available via the ICSP connector. You will need to connect pins D11 - D13 to the appropriate pins on the Leonardo ICSP connector to use this shield.
3. Arduino Mega - SPI pins are D50, D51, and D52 so these will need to be mapped from the D11-D13 pins on the shield. Also, D53 is normally used for SS rather than D10. On a Mega, A4 and A5 are not used for I2C but the shield should map A4 and A5 to the I2C pins next to AREF. You may also have the same problem with the USB type B connector.

از این پس درج نظرات صرفا از طریق سامانه آفتاب یار امکان پذیر می باشد، برای وارد شدن به صفحه کالا بر روی لینک زیر کلیک کنید:
http://aftabyar.com/page/aftab-1661.html
AftabRayaneh©2022