برد آردوینو مگا Arduino Mega2560 CH340

1. پروژه های الکترونیک
2. آموزشی
3. صنعت
   

1. میکروکنترلر:ATmega2560
2. ولتاژ عملیاتی:5V
3. ولتاژ ورودی (پیشنهادی): 9 ~ 7 ولت
4. ولتاژ ورودی (محدوده):20 ~ 6 ولت
5. پین های دیجیتال ورودی/خروجی:54 (15تای آن به عنوان خروجی PWM استفاده می شود)
6. پین های آنالوگ ورودی: 16
7. جریان DC هر پین ورودی/خروجی: 40 میلی آمپر
8. جریان DC پین 3.3 ولتی: 50 میلی آمپر
9. حافظه فلش:256 کیلوبایت (8 کیلوبایت از آن توسط BootLoader استفاده می شود)
10. SRAM: 8KB
11. EEPROM: 4KB
12. سرعت ساعت: 16MHz
    

Description:
The MEGA 2560 is designed for more complex projects. With 54 digital I/O pins, 16 analog inputs and a larger space for your sketch it is the recommended board for 3D printers and robotics projects. This gives your projects plenty of room and opportunities. The ATmega2560 on the Mega 2560 comes preprogrammed with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol. The Mega 2560 can be powered via the USB connection or with an external power supply. The power source is selected automatically. The ATmega2560 has 256 KB of flash memory for storing code (of which 8 KB is used for the bootloader), 8 KB of SRAM and 4 KB of EEPROM (which can be read and written with the EEPROM library). The Mega 2560 board has a number of facilities for communicating with a computer, another board, or other microcontrollers. The ATmega2560 provides four hardware UARTs for TTL (5V) serial communication.
Each of the 54 digital pins on the Mega can be used as an input or output, using pinMode(), digitalWrite(), and digitalRead() functions. They operate at 5 volts. Each pin can provide or receive 20 mA as the recommended operating condition and has an internal pull-up resistor (disconnected by default) of 20-50 k ohm. A maximum of 40mA is the value that must not be exceeded to avoid permanent damage to the microcontroller. The Mega 2560 has a resettable polyfuse that protects your computer's USB ports from shorts and overcurrent. Although most computers provide their own internal protection, the fuse provides an extra layer of protection. If more than 500 mA is applied to the USB port, the fuse will automatically break the connection until the short or overload is removed.
The Mega 2560 board contains a trace that can be cut to disable the auto-reset. The pads on either side of the trace can be soldered together to re-enable it. It's labeled "RESET-EN." You may also be able to disable the auto-reset by connecting a 110-ohm resistor from 5V to the reset line.

Application:
Projects
industrials
education

Feature:
Microcontroller: ATmega2560
Operating Voltage: 5V
DC Current per I/O Pin: 40 mA
DC Current for 3.3V Pin: 50 мА
Digital I/O Pins: 54
PWM: 14
Analog Input Pins: 16
Flash Memory: 256 KB
SRAM: 8 KB
Bootloader: 8 KB
EEPROM: 4 KB
Clock Speed: 16 MHz
USB cable: Сomplete set
Size: 10.2 x 5.3