هوالرزاق


دسته بندی
سنسور رطوبت و دما مدل DHT11
سنسور رطوبت و دما مدل DHT11 سنسور رطوبت و دما مدل DHT11 سنسور رطوبت و دما مدل DHT11 سنسور رطوبت و دما مدل DHT11

سنسور رطوبت و دما مدل DHT11

کد انبار : 157-78-1113
مدل کالا : DHT11-SENSOR
جستارش : A1-06-0806B
موجودی: 109
قیمت:
42,900 تومان

تعداد: - +
   - یا -   

سنسور رطوبت و دما مدل DHT11

سنسور دما و رطوبت DHT11 ، یک سنسور  ارزان قیمت جهت سنجش دما و رطوبت هواست. اندازه کوچک این سنسور، مصرف کم انرژی و انتقال سیگنال به مسافتی بیش از 20 متر، آن را به یکی از بهترین گزینه ها جهت استفاده در پروژه های مختلف تبدیل کرده است. با توجه به خروجی دیجیتال این سنسور، به راحتی می تواند به برد آردوینو و یا سایر میکروکنترلر ها متصل گردد.


کاربرد سنسور DHT11 :

  1. سیستم های اتوماتیک کنترل هوا
  2. سیستم های پزشکی
  3. تجهیزات مصرفی
  4. تجهیزات کنترلی
  5. ایستگاه هواشناسی
  6. موارد مختلف صنعتی

مشخصات سنسور رطوبت و دما مدل DHT11:

  1. قیمت ارزان
  2. ولتاژ عملیاتی و ورودی/خروجی 3 تا 5 ولت
  3. حداکثر جریان استفاده شده هنگام عملیات تبدیل 2.5 میلی آمپر
  4. مناسب برای خواندن رطوبت 20 تا 95% با دقت 5%
  5. مناسب برای خواندن دمای 0 تا 50 درجه با دقت 2± سانتی گراد
  6. نرخ نمونه برداری 1 هرتز (یکبار در ثانیه)
  7. اندازه : 16 × 12 × 6 میلی متر
  8. دارای 4 پین با 0.1 اینچ فاصله

مستندات:
اطلاعات بیشتر و دریافت نمونه کدهای آردوینو و مثال ها سنسور DHT11


Description:
DHT11 is an inexpensive sensor that provides calibrated digital outputs for ambient temperature and relative humidity. The relative humidity is the amount of water vapor in air vs. The saturation point of water vapor in the air. At the saturation point, water vapor starts to condense and accumulate on surfaces forming dew.
It comes in a single row 4-pin package and operates from 3.5 to 5.5V power supply. The humidity sensing component is a moisture holding substrate with electrodes applied to the surface. It can measure temperature from 0-50 °C with an accuracy of ±2°C and relative humidity ranging from 20-95% with an accuracy of ±5%. It has got its own proprietary 1-wire protocol, therefore, the communication between the sensor and a microcontroller is not possible with any of its peripherals through a direct interface. The protocol must be implemented in the firmware of the MCU through bit-banging of an I/O pin.
The DHT11 detects water vapor by measuring the electrical resistance between two electrodes. When water vapor is absorbed by the substrate, ions are released by the substrate which increases the conductivity between the electrodes. The change in resistance between the two electrodes is proportional to the relative humidity. Higher relative humidity decreases the resistance between the electrodes, while lower relative humidity increases the resistance between the electrodes.
The DHT11 uses just one signal wire to transmit data to the Arduino. Power comes from separate 5V and ground wires. A 10K Ohm pull-up resistor is needed between the signal line and the 5V line to make sure the signal level stays high by default.

Applications:
HVAC
Testing and inspection equipment
Automotive
Data Logger
Consumer goods
Automatic control
Weather station
Home appliances
Humidity regulator
Medical
Dehumidifier

Features:
Model: DHT11
Output Type: Digital
Input voltage: 3.5V ~ 5.5V
Resolution: 8 bit
Humidity Accuracy: +/- 5% RH (at 25°C)
Temperature Accuracy: +/- 2°C (at 25°C)
Humidity Range: 20% ~ 95% RH
Temperature Range: 0°C ~ 50°C
Maximum Response Time: 15s (Humidity), 30s (Temperature)
Interface: 1 Wire
Pin Number: 4 Pins
Size:12.5mm x 16mm x 6mm
از این پس درج نظرات صرفا از طریق سامانه آفتاب یار امکان پذیر می باشد، برای وارد شدن به صفحه کالا بر روی لینک زیر کلیک کنید:
http://aftabyar.com/page/aftab-157.html
AftabRayaneh©2022