هوالرزاق


دسته بندی
باکس پلاستیکی 56x58x28 میلی متر
باکس پلاستیکی 56x58x28 میلی متر باکس پلاستیکی 56x58x28 میلی متر باکس پلاستیکی 56x58x28 میلی متر باکس پلاستیکی 56x58x28 میلی متر باکس پلاستیکی 56x58x28 میلی متر باکس پلاستیکی 56x58x28 میلی متر

باکس پلاستیکی 56x58x28 میلی متر

کد انبار : 6312-422-10273
مدل کالا : YD - D - 42
جستارش : B2-07-0304A
موجودی: 236
قیمت:
35,580 تومان

تعداد: - +
   - یا -   

باکس پلاستیکی (جعبه اتصال) 56x58x28 میلی متر

باکس يا جعبه تقسيم برق محفظه ای برای انشعاب و اتصالات برق مي باشد که دارای دو نوع تو کار و روکار می باشد و جنس آن نوع کائوچو يا پلاستيکی و نوع فلزی می باشد. اطراف آن براي ورود لوله يا گلند لوله شيارهايی طراحی شده تا اتصالات ورودی و خروجی از طريق آن به آسانی امکان پذير بوده و پس از اتصال سيمها، درب روي آن بسته و معمولا دارای واشر آب بندی می باشد که از ورودی آب و گرد و غبار به داخل محفظه جلوگيری می نماید. جعبه تقسیم قطعه برای سربندی سيم ها و اتصالات كه هم به جهت متمركز شدن اتصالات و همچنين عايق نمودن آنها به كار می رود. جعبه تقسيم هاي ABS مقاومت قابل توجهی در مقابل نور خورشيد را داراست. جعبه‌های تقسیم ضد آب اگر به‌درستی نصب شوند می توانند به خوبی از سیم ها و وسایلی که داخلشان هست، محافظت کرده و مانع از خیس شدن و قطعی آن‌ها شوند. پلاستیکی بودن جعبه تقسیم و نارسانا بودن آن سبب می‌شود تا در صورت تماس سیم‌ها با بدنه جعبه تقسیم ، اختلال و قطعی به وجود نیاید.

کاربرد جعبه اتصال :

  1. محفظه کنتور برق
  2. محفظه ابزار
  3. محفظه پلاستیکی
  4. باتری لیتیومی
  5. و...

مشخصات جعبه اتصال :

  1. مدل: YD-D-42
  2. اندازه: 56 × 58 × 28 میلی متر
  3. جنس: ABS
  4. وزن: 24 گرم

Description:
This white project box of 56mm x58mm x 28mm is suitable for the installation of projects. With the vertical slots on the inside, several PCBs can be mounted in the box. With the screws on the top, the whole box can be closed securely.
Circuit boards are found in nearly every electronic device and are the predominant technology by which electrical circuits are assembled. While printed circuit boards are flexible, they can be damaged by mechanical shock or flexing. As a result, they require sturdy mounting to protect them from damage. The boards also contain uninsulated components on both sides, which means contact with a metal enclosure can cause electrical shorts and malfunctions.

Instructions:
1. Locate the holes on your circuit board. Mass-produced circuit boards usually have 1/4-inch holes in each of the corners which can be used for mounting.
2. Hold the circuit board directly over the location you wish to mount it and mark the location of the screw holes on the enclosure.
3. Mount the printed circuit board to the stand-off spacers. Place a nylon washer over the top of the drilled hole, and insert screw through the hole. Secure the screw to one of the stand-offs. The thread on the screw should match the stand-offs. Repeat with the other screw holes.
4. Drill holes through the enclosure at the locations marked.
5. Place the circuit board with the stand-offs mounted to it over the holes drilled into the enclosure. Place a long screw into each hole and tighten, driving the screw into the bottom of the standoff. Repeat with the other screws.

Application:
Power meter housing
hand-held instrument housing
instrument housing
plastic housing
lithium battery
can be used in engineering, electronics and other industries.

Features:
Model: YD-D-42
Size: 56 x 58 x 28mm
Material: ABS
Weight:24gr

از این پس درج نظرات صرفا از طریق سامانه آفتاب یار امکان پذیر می باشد، برای وارد شدن به صفحه کالا بر روی لینک زیر کلیک کنید:
http://aftabyar.com/page/aftab-6312.html
AftabRayaneh©2022