هوالرزاق


دسته بندی
بسته 2 تایی پولی هرزگرد بدون دندانه GT2 مخصوص پرینتر سه بعدی شفت 5 میلیمتری
بسته 2 تایی پولی هرزگرد بدون دندانه GT2 مخصوص پرینتر سه بعدی شفت 5 میلیمتری بسته 2 تایی پولی هرزگرد بدون دندانه GT2 مخصوص پرینتر سه بعدی شفت 5 میلیمتری بسته 2 تایی پولی هرزگرد بدون دندانه GT2 مخصوص پرینتر سه بعدی شفت 5 میلیمتری

بسته 2 تایی پولی هرزگرد بدون دندانه GT2 مخصوص پرینتر سه بعدی شفت 5 میلیمتری

کد انبار : 1644-167-3020
مدل کالا : pulley wheel GT2-5
جستارش : A1-08-1003A
موجودی: 90
قیمت:
81,360 تومان

تعداد: - +
   - یا -   

بسته 2 تایی پولی هرزگرد بدون دندانه GT2 مخصوص پرینتر سه بعدی شفت 5 میلیمتری

پولی ها به منظور تغییر مسیر و افزایش نیروی اعمال شده به یک بار مورد استفاده قرار می گیرند که در نتیجه موجب صرفه جویی در مصرف انرژی می شوند. پولی ها به صورت ثابت، متحرک و یا ترکیبی از هر دو می باشند. پولی های تایمینگ در سیستم های انتقال قدرت استفاده می شوند و نسبت سرعت در طراحی آن ها خیلی مهم می باشد. این پولی ها بسیار با دوام و پر کاربرد هستند.
برای انتقال حرکت چرخشی استپر موتور نیاز به بخش های مختلف از پولی و تسمه تایمینگ استفاده می شود.
 استفاده از پولی هرزگرد باعث کاهش لغزش و حرکت گسسته ی استپر موتور می شود. بهترین انتخاب برای پرینتر های سه بعدی برای افزایش دقت استفاده از تسمه تایمینگ و پولی است.
هر چه تعداد دندانه های پولی ها بیشتر باشد دقت چاپ بالاتر خواهد بود.

مشخصات:
مدل: پولی هرزگرد GT2-20
فاقد دندانه
قطر کلی پولی: 18 میلی متر
قطر محل قرارگیری تسمه: 12 میلی متر
شفت: 5 میلی متر
اندازه: 27 × 16 × 16 میلی متر

Description:
The GT2 series of belts and pulleys are designed specifically for linear motion. They use a rounded tooth profile that guarantees that the belt tooth fits smoothly and accurately in the pulley groove, so when you reverse the pulley direction, there is no room for the belt to move in the groove.
In a belt drive system, idlers are often used to alter the path of the belt, where a direct path would be impractical.
Idler pulleys are also often used to press against the back of a pulley in order to increase the wrap angle (and thus contact area) of a belt against the working pulleys, increasing the force-transfer capacity.
Belt drive systems commonly incorporate one movable pulley which is spring or gravity-loaded to act as a belt tensioner, to accommodate stretching of the belt due to temperature or wear. An idler wheel is usually used for this purpose, in order to avoid having to move the power-transfer shafts.
Driver pulleys can be fastened to a shaft or bar as opposed to driver pulleys which have a bearing allowing them to rotate freely. Most driver pulleys can be fastened using two set screws, resulting in a reliable setup. For guiding the belt, we offer two types of driven pulleys: with and without teeth (smooth). Driven pulleys allow you to guide the teeth side of the belt without vibrations that would have been caused by running them over a smooth surface.
Idler pulleys are used to take up the slack, change the direction of transmission, or provide clutching action. Idler pulleys are rollers that do not produce any mechanical advantage, nor transmit power to a shaft. Idler pulleys are used to lead a chain around a bend or to take up slack in a drive chain.

Features:
Material: Aluminum
Bore: 5mm
Total Size: 16 × 16 × 27mm (L*W*H)

از این پس درج نظرات صرفا از طریق سامانه آفتاب یار امکان پذیر می باشد، برای وارد شدن به صفحه کالا بر روی لینک زیر کلیک کنید:
http://aftabyar.com/page/aftab-1644.html
AftabRayaneh©2022