هوالرزاق


دسته بندی
هیت بد ( PCB Heated Bed ) پرینترهای سه بعدی RepRap
هیت بد ( PCB Heated Bed ) پرینترهای سه بعدی RepRap هیت بد ( PCB Heated Bed ) پرینترهای سه بعدی RepRap هیت بد ( PCB Heated Bed ) پرینترهای سه بعدی RepRap

هیت بد ( PCB Heated Bed ) پرینترهای سه بعدی RepRap

کد انبار : 653-167-1675
مدل کالا : HEATBED-MK2B
جستارش : A2-12-0502A
موجودی: 51
قیمت:
293,600 تومان

تعداد: - +
   - یا -   

هیت بد ( PCB Heated Bed ) پرینترهای سه بعدی RepRap

**رنگ هیت بد ارسالی ممکن است قرمز یا مشکی باشد.

یکی از مسائل مهم در کار با پرینتر های سه بعدی این است که در هنگام خشک شدن ماده ی پلاستیکی مذاب پرینت شده، قطعه به صفحه ی زیرین می چسبد و در هنگام برداشتن قطعه ی پرینت شده باعث آسیب رسیدن به قطعه می شود. برای حل این مشکل از صفحه های گرم برای مذاب ماندن فصل مشترک بستر و قطعه ی پلاستیکی استفاده میشود. هیت بد با گرم کردن قطعه و ثابت نگه داشتن دمای آن باعث می شود تا قطعه شما با بهترین کیفیت چاپ شده و از بروز تنش های پس ماند که به واسطه تفاوت دمای داخل و بیرون قطعه (و نیز تفاوت سطوح ابتدایی و بالایی) ایجاد می شود جلوگیری می کند.
حرارت را در این کالا را با یک عدد ترمیستور میتوانید اندازه گیری کنید. گرما در این مدل یکنواخت و به صورت پشت و رو انتقال می یابد. حداکثر دما به آمپر تغذیه ارتباط مستقیم دارد. مقدار ولتاژ آن به عواملی مانند دمای محیط، نوع تهویه، نوع اعمال جریان ،نحوه اتصال و نوع سیم تغذیه بستگی دارد. توجه داشته باشید برای استفاده از هیت بد بر روی دستگاه خود باید منبع تغذیه قدرتمندی داشته باشید زیرا که این قطعه برای گرم شدن به جریان زیادی نیاز دارد.
به طور کلی اگر بخواهیم توضیحاتی راجع به عملکرد هیت بد دهیم، هیت بد زیر قطعه پرینت سه بعدی قرار می گیرد و با استفاده از اتصالات (پیچ و فنر) به سازه پرینتر متصل و تنظیم می شود. هیت بد دارای سیم اتصال به جریان هست که این جریان نقش گرم کردن هیت بد را دارد. همچنین یک ترمیستور (سنسور دما) به هیت بد متصل شده تا بتوانید آن را در دمای مناسب نگه دارید. تمام این سیم ها به برد کنترل کننده پرینتر سه بعدی (مثل Ramps) وصل می گردد.
 

Description:
The PCB still has a side with the traces on and a side without but now the silkscreen is on both the top and bottom, this makes it look good even when 'upside-down' under a layer of glass. The LED, resistor, and power wires can be mounted on either side of the board, with either surface mount or through-hole components. If you are using through-hole be careful when soldering not to interfere with the glass and introduce a gap between the glass and the PCB. If the MK2 board is made properly without copper plating then be sure to only solder the LED and resistor to the same side and the tracks. This problem is solved in the MK2a by removing the pads on the non-connected side. This heat bed keeps the extruded melted plastic and prevents warping. The LEDs are optional, but if you choose to use the LEDs you MUST install the resistor.
The PCB heat bed has two sides, one with the copper traces (bottom side) and one without (top). On older versions of the PCB heat bed, only the side without traces carried a silkscreen. Currently (as of January 2015) PCB heat beds are silkscreened on both sides.
Previously, printing on the top side was considered to be safer as the copper traces could be damaged if the print head would collide with the heat bed surface (if for example, the Z-min end stop malfunctioned). Obviously, if a piece of glass is used as the print surface, it protects the PCB copper traces. However, make sure your heat bed mounting springs are not too strong to prevent damage to the glass in case of an accidental collision.
Note that the LED, resistor and wire connections are also liable to accidentally collide with the print head.
when the PCB heat bed is used with a piece of glass as the build surface is to mount the PCB heat bed with the traces up. This improves heat transfer to the glass and the PCB heats up faster.

Features:
Dual Power: 12V or 24V
Fast Heat Up
Dimensions (Outer): 214 x 214mm
Dimensions (Heat Bed): 200 x 200mm
Laminate FR4 1.6±0.15mm
2 Layer, 35μm Copper
Copper Plated Holes
Red Solder mask both sides
White Silk screen both sides

Test report:
12V, with the increase of temperature, the current decline (physical knowledge: resistance increases with temperature change)
24V, the theoretical maximum current is less than 5A.

از این پس درج نظرات صرفا از طریق سامانه آفتاب یار امکان پذیر می باشد، برای وارد شدن به صفحه کالا بر روی لینک زیر کلیک کنید:
http://aftabyar.com/page/aftab-653.html
AftabRayaneh©2022