هوالرزاق


دسته بندی
ماژول رله 5 ولت چهار  کاناله
ماژول رله 5 ولت چهار  کاناله ماژول رله 5 ولت چهار  کاناله ماژول رله 5 ولت چهار  کاناله

ماژول رله 5 ولت چهار کاناله

تولید کننده: Aftab
کد انبار : 86-73-1030
مدل کالا : RELAY-4CH
جستارش : B1-05-0302A
موجودی: 18
قیمت:
99,980 تومان

تعداد: - +
   - یا -   

ماژول رله 5 ولت چهار کاناله

ماژول رله 4 کاناله 5 ولت دارای 4 عدد رله بر روی یک برد بوده که هر یک قادر هستند تا ولتاژ AC را حداکثر تا 250 ولت با شدت جریان 10 آمپر تحمل نمایند و حداکثر ولتاژ DC قابل تحمل برای آنها برابر با 30 ولت همراه با جریان 10 آمپر می باشد. بر روی برد این ماژول الکترونیک یک ال ای دی قرار گرفته است که وضعیت رله را نمایش می دهد. این قطعه که در بازار برق و الکترونیک به فروش می رسد، دارای ولتاژی برابر با 5 ولت DC می باشد. ورودي فعال ساز رله Active low مي باشدو اين به اين معني است كه براي روشن كردن رله بايستي پين خروجي آردوينو را Low كرد و براي خاموش كردن رله بايد پين خروجي رله را High كرد. در این ماژول از اپتوکوپلرها برای قطع و وصل شدن رله ها استفاده می گردد.


کاربرد رله چهار کانال 5 ولت:

  1. کنترل درب های برقی
  2. سنسورهای روشنایی راهروها
  3. کنترل موتورها(متناسب با توان رله)
  4. استفاده در سیستم های کنترل پیامکی رله
  5. کنترل انواع وسایل برقی نظیر لامپ ها(متناسب با توان رله)
  6. قابلیت به کار گیری در خانه های هوشمند جهت کنترل وسایل برقی


مشخصات رله چهار کانال 5 ولت:

  1. ابعاد: 3 × 7 × 10 سانتی متر
  2. ولتاژ راه انداز: 0 ولت
  3. وزن: 61 گرم
  4. رله: Songle تک قطبی (اُپتوایزولاتور، محافظت از پارازیت خوب)
  5. رابط استاندارد: (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic active low)

مستندات:
نمونه کد های برد رله آردوینو


Description:
This is a 5V 4-channel relay interface board, and each channel needs a 15-20mA driver current. It can be used to control various appliances and equipment with large current. It is equipped with high-current relays that work under AC250V 10A or DC30V 10A. It has a standard interface that can be controlled directly by a microcontroller.
5V Relay Module is a relay board that you can control its contacts with 5V via Arduino or another microcontroller board.
It draws 20mA of current from microcontroller when triggering. It is used frequently in the hobby, industrial and robotics projects.
It can relay current up to 10A at 30VDC or 220VAC. The board has control LEDs for each relay.
When the input terminals (IN1, IN2, IN3, IN4) are supplied with low-level signals, you can see relay K1, K2, K3, K4 closed successively and repeat this cycle. In order to show its ability to drive load more intuitively, two LEDs are connected to relay K1 and K2.

Features:
Dimensions: 10x7x3 cm
Trigger Voltage:0V
Weight: 61g
PCB Color: Blue
4 fixed screw holes at each corner of the board for install and fix. (The diameter is 3.1mm)
High-quality Songle relay with single pole double throw, a common terminal, a normally open terminal, and a normally closed terminal
Optical coupling isolation, good anti-interference.
Standard interface (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic active low)
Opto-isolated inputs
Closed at a low level with the indicator on, released at a high level with indicator off

Pin Description:
VCC: Positive supply voltage
GND: Ground
IN1--IN4: Relay control port
از این پس درج نظرات صرفا از طریق سامانه آفتاب یار امکان پذیر می باشد، برای وارد شدن به صفحه کالا بر روی لینک زیر کلیک کنید:
http://aftabyar.com/page/aftab-86.html
AftabRayaneh©2022