هوالرزاق


دسته بندی
شیلد موتور درایور مونستر موتو Monster Moto ) VNH2SP30 ) با قابلیت درایو 30A
شیلد موتور درایور مونستر موتو Monster Moto ) VNH2SP30 ) با قابلیت درایو 30A شیلد موتور درایور مونستر موتو Monster Moto ) VNH2SP30 ) با قابلیت درایو 30A شیلد موتور درایور مونستر موتو Monster Moto ) VNH2SP30 ) با قابلیت درایو 30A شیلد موتور درایور مونستر موتو Monster Moto ) VNH2SP30 ) با قابلیت درایو 30A شیلد موتور درایور مونستر موتو Monster Moto ) VNH2SP30 ) با قابلیت درایو 30A

شیلد موتور درایور مونستر موتو Monster Moto ) VNH2SP30 ) با قابلیت درایو 30A

کد انبار : 496-68-1490
مدل کالا : VNH2SP30
موجودی: تامین کالا فقط به صورت سفارشی پیش سفارش
قیمت:
100,850 تومان

تعداد: - +
   - یا -   

شیلد موتور درایور مونستر موتو Monster Moto ) VNH2SP30 ) با قابلیت درایو 30A

 جهت دریافت نمونه کد آردوینو و مشاهده سیم بندی به این لینک مراجعه نمایید.
شیلد Monser Moto در اصل نسخه ی بالاتر از شیلد درایور Ardumoto است. در این شیلد یک جفت درایور VNH2SP30 full-bridge با درایور L298H-bridge جایگزین شده است. همچنین مدار این برد برای ایجاد قابلیت راه اندازی یک جفت موتور با مصرف جریان بالا تقویت شده است. VIN و خروجی موتور برد برای ترمینال پیچی 5mm آماده شده است.توجه داشته باشید درصورتی که ازین برد برای کابردهایی با مصرف جریان بالا استفاده می کنید. ممکن است برای بهبود عملکرد نیاز به یک هیت سینک یا فن و لحیم کردن سیم مستقیما بر روی برد بجای استفاده از ترمینال پیچی داشته باشید. اگرچه در هنگام استفاده ازاین برد برای جریان های تا 6A به سختی چیپ آن بطور قابل ملاحظه ای گرم می شود .

مشخصات:
ولتاژ ماکزیمم: 16V
حداکثر جریان نامی : 30A
جریان دهی پیوسته عملی: 14A
سنجش جریان قابل استفاده برای پین آنالوگ آردینو
ماسفت در هنگام مقاومت : 19mΩ
فرکانس PWM ماکزیمم: 20KHz
قابلیت shutdown حرارتی برای محافظت
قابلیت قطع خودکار مدار در صورت کاهش و افزایش بیش از حد ولتاژ

Description:
VNH2SP30 is a full-bridge motor driver intended for a wide range of automotive applications. The device incorporates a dual monolithic high side driver and two low side switches. The high side driver switch is designed using the STMicroelectronics well known and proven proprietary VIPower M0 technology which permits efficient integration on the same die of a true Power MOSFET with an intelligent signal/protection circuitry. The VIN and motor out are pitched for 5mm screw terminals, making it easy to connect larger gauge wires. INA and INB control the direction of each motor, and the PWM pins turn the motors on or off. For the VNH2SP30, the current sense (CS) pins will output approximately 0.13 volts per amp of output current. It is replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. It also set up to support circuitry so this board is capable of driving a pair of high-current motors. Both the input end of the module and the motor interface use 5mm interface terminals, making it convenient to connect large-size wires.

Note:
When using this board in extreme high-demand applications it may be necessary to improve thermal performance with a heat-sink or fan and to solder the wires directly to the board instead of using a screw terminal (in addition to the myriad other complications present in a high-current system) However when using the board at currents up to 6A the chips will barely become noticeably warm.

Features:
Maximum input voltage: 16V
Peak drive current: 30A
Continuous starting current: 14A
Maximum PMW frequency: 20 kHz
Output impedance is only 19m Ω
Current can be detected by Arduino analog input pin
With over-temperature protection, over-voltage, and under-voltage protection

از این پس درج نظرات صرفا از طریق سامانه آفتاب یار امکان پذیر می باشد، برای وارد شدن به صفحه کالا بر روی لینک زیر کلیک کنید:
http://aftabyar.com/page/aftab-496.html
AftabRayaneh©2022